- Refrigeration Trainers
- Heating & AC Trainers
- HVAC & Refrigeration Trainers
- Building Automation Controls
Designed for the student that has a working knowledge of the theory of refrigeration. Students are asked to design a system to match specifications of a particular situation. Instruction kit and experiment manual provide set-up and assembly directions.
Sight glass tubes at inlet and outlet of evaporator and condenser constructed of explosion proof, tie-bolt design. Features: cut-out and by-pass valves, hand valves to simulate malfunctions, combination low pressure control and high pressure cut-out, thermostatic control, 2 solenoid liquid line valves. Includes Lab Manual, Operation Instructions, and an iManifold Kit for full diagnostic testing and troubleshooting.
This deluxe dual-application commercial refrigeration trainer can show operation of multi-evaporator systems, dual temperature applications (low and medium) and an electric resistant heat defrost cycle. Includes an iManifold Kit for full diagnostic testing and troubleshooting of system components.
This freestanding, self-contained trainer enables students to learn principles of commercial and industrial refrigeration systems. Features: semi-hermetic compressor with 2HP capacity, crankcase heater with auto controls, 2 forced air evaporators and 2 standard water cooled condenser and hot gas by-pass system. Includes Instructor Guide and an iManifold Kit for full diagnostic testing and troubleshooting.
This refrigeration demonstrator uses the 4 main parts of the refrigeration system (condenser, compressor, evaporator and control device) that demonstrate basic refrigeration principles. The components then work together to cool a small enclosed refrigerator compartment fully featured with an electronic temperature control device. Includes: Lab Manual and iManifold Kit for full diagnostic testing and troubleshooting of system components.
Designed for the student with a working knowledge of the theory of refrigeration electrical control systems. Using this trainer, students are required to design a system to match specifications of a particular situation. Connections between components are wired by the students.
This trainer provides real world experience in troubleshooting wiring, piping and controls of a working air conditioning unit for a whole house. Features: fault simulation, real-world applications, sight glass for direct observation, and visible wiring and piping. Includes Lab Manual, Refrigeration and Air Conditioning Technology book, and iManiforld Kit for full diagnostic testing and troubleshooting.
The forced air and hydronic heating trainer provides demonstration and service practice with forced air and hydronic heating systems, including hot water heating systems. All components are full size, completely operational and are standard brands of equipment. Includes: Lab Manual, Refrigeration and Air Conditioning Technology and Heat Pump books, and student assignments.
This trainer is perfect for students to learn the basics of electric heat control systems. Features: complete operating controls, wired 3 element furnace circuit, simulated heater elements, sequences, klixon limit switch, fusible link safety device, thermostat, transformer and fan delay control.
This trainer provides real world experience in troubleshooting wiring, piping and controls of a working air conditioning unit for a whole house. Features: fault simulation with two refrigerant faults and four electrical faults, real-world applications and troubleshooting examples, sight glass for direct observation, visible wiring and piping, and more. Includes: Lab Manual, Heat Pumps book, and iManifold Kit for full diagnostic testing and troubleshooting of system components.
The control board contains a complete set of electrical controls of a furnace, with air conditioning, to demonstrate basic principles and provide electrical service experience. Features mounted components panel, equipped for both thermocouple and thermopile systems, signal lamps show simulated operation.
This tabletop trainer provides real world experience in troubleshooting wiring, piping and controls on a working heat pump unit. The trainer is perfect for introduction to heat pump theory. Features: pre-piped, pre-wired unit, observable heat pump cycle, pressure, temperature and electrical gauge readings, optional add-on equipment packages.
This Trainer Panel is used to demonstrate electrical principles similar to those found in a residential dwelling. The inclusion of the dual 24 VAC power supply makes this a very useful trainer for introductory classes. Students learn wiring as well as the proper electrical hookups from the manual that is included. All components are mounted on a hardwood panel.
With this demonstrator, students gain a full understanding of National Electrical Code residential electrical circuits. Through actual practice, students attain a substantial beginning level skill and proficiency using tools of the electrical trade. Includes: two books on Electrical Code and Electrical Wiring.
This training unit demonstrates basic refrigeration and air conditioning principles in a compact size, perfect for in the classroom or mobile training. Features: lightweight unit, variable fan for adjustment, sight glasses, explosion-proof tie bolt design, and observable operation.
This table-top Air Conditioning and Refrigeration Training Unit demonstrates basic refrigeration and air conditioning principles in a compact size perfect for in the classroom or mobile training. Training Unit comes with a standard-range iConnect System Analyzer kit by iManifold for real-time performance analysis.
PT-181 is a packaged learning system that combines a portable BAS/HVAC controls simulator with a “Building Automation & HVAC Controls – Level 1 Introductory Course” curriculum. The student is introduced to most of the major components used in modern “Smart Buildings.”
PT-201 is a packaged learning system combining a portable BAS controller & controls wiring simulator with an “Intro to Building Automation Controllers” curriculum. This package allows students to wire all inputs and outputs using the provided banana plug assemblies.
BL-02 packaged benchtop learning system, intended for Building Automation and HVAC controls technicians/programmers who work with BAS controllers also includes CO2/Temp “Wall setter” and analog actuator to add HVAC input/output device learning options to the web-based Level 1 curriculum.
BL-01 packaged benchtop learning system is intended for Building Automation and HVAC controls technicians/programmers who work with BAS controllers. Input/output devices are prewired. The Level 1 curriculum is web-based and highly interactive emphasizing BACnet networking and Sedona programming.
Providing the HVAC/R student with the knowledge & training for the safe and efficient operation of all types of systems found in our industry.
iConnect Training provides the finest training units to the educational market. They can be found in high schools, technical colleges, government facilities and other educational settings all over the world.
The training units in iConnect’s catalog represent a wide variety of subjects in the heating, refrigeration and air conditioning industries. Whether you’re looking to demonstrate simple concepts or illustrate advanced troubleshooting and servicing techniques to your students, Klein Educational can help you choose the perfect iConnect Training System for your program.